Enum BalanceOp

pub enum BalanceOp<T: LazyBalanceMarker, M: ManualBalanceModel<T>> {
    Deposit(M::User, T::Asset, T::Subject),
    Withdraw(M::User),
    Mint(T::Asset, T::Subject),
    Reap(T::Asset, T::Subject),
    Drain,
}

Operation descriptor for driving both LazyBalance and ManualBalanceModel executions in a consistent manner.

Each variant represents a high-level balance action along with the required inputs. These operations are typically used in testing or simulation to:

• execute the lazy balance model
• pass the resolved results into a manual (eager) model
• compare and validate behavior across both systems

Variants

Deposit(M::User, T::Asset, T::Subject)

Deposit operation.

(user, amount, subject) where:

• user is the target account
• amount is the requested asset value
• subject defines execution intent (e.g., precision/behavior)

Withdraw(M::User)

Withdraw operation.

(user) where:

• user is the account performing withdrawal

Mint(T::Asset, T::Subject)

Mint operation.

(amount, subject) where:

• amount is the asset value to introduce
• subject defines execution intent

Reap(T::Asset, T::Subject)

Reap operation.

(amount, subject) where:

• amount is the asset value to remove or adjust
• subject defines execution intent

Drain

Drain (Full-Reap) operation.

Resets the entire balance state.

Trait Implementations

impl<T: Clone + LazyBalanceMarker, M: Clone + ManualBalanceModel<T>> Clone for BalanceOp<T, M>

where M::User: Clone, T::Asset: Clone, T::Subject: Clone,

fn clone(&self) -> BalanceOp<T, M>

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl<T: Debug + LazyBalanceMarker, M: Debug + ManualBalanceModel<T>> Debug for BalanceOp<T, M>

where M::User: Debug, T::Asset: Debug, T::Subject: Debug,

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl<T: Ord + LazyBalanceMarker, M: Ord + ManualBalanceModel<T>> Ord for BalanceOp<T, M>

where M::User: Ord, T::Asset: Ord, T::Subject: Ord,

fn cmp(&self, other: &BalanceOp<T, M>) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized,

Restrict a value to a certain interval.

impl<T: PartialEq + LazyBalanceMarker, M: PartialEq + ManualBalanceModel<T>> PartialEq for BalanceOp<T, M>

where M::User: PartialEq, T::Asset: PartialEq, T::Subject: PartialEq,

fn eq(&self, other: &BalanceOp<T, M>) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl<T: PartialOrd + LazyBalanceMarker, M: PartialOrd + ManualBalanceModel<T>> PartialOrd for BalanceOp<T, M>

where M::User: PartialOrd, T::Asset: PartialOrd, T::Subject: PartialOrd,

fn partial_cmp(&self, other: &BalanceOp<T, M>) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

Tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

Tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

Tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

Tests greater than or equal to (for self and other) and is used by the >= operator.

impl<T: Copy + LazyBalanceMarker, M: Copy + ManualBalanceModel<T>> Copy for BalanceOp<T, M>

where M::User: Copy, T::Asset: Copy, T::Subject: Copy,

impl<T: Eq + LazyBalanceMarker, M: Eq + ManualBalanceModel<T>> Eq for BalanceOp<T, M>

where M::User: Eq, T::Asset: Eq, T::Subject: Eq,

impl<T: LazyBalanceMarker, M: ManualBalanceModel<T>> StructuralPartialEq for BalanceOp<T, M>